Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Duncanville
Gate repair in Duncanville almost always starts below the surface. The Blackland Prairie clay under this city swells in spring and shrinks in summer, and that movement is what loosens posts, throws gates out of square, and burns out operators. If your gate needs to be lifted to latch, the hinges are rarely the real problem. That’s why our crews look at the footing before we ever touch the hardware. We serve Duncanville’s 75116, 75137, and 75138 ZIP codes from our Dallas-Fort Worth office, with a live person answering the phone 24 hours a day. Call (936) 226-3481 for a free estimate.
Why Ironworks Gate Co. Is Duncanville’s Preferred Gate Repair Company
We’ve been doing this work for over 42 years, founded in 1984, and the gates we repair in Duncanville are often older than the technicians fixing them. That experience matters here specifically. A 1970s brick ranch off East Wheatland Road has different problems than a newer build near Cedar Ridge, and a gate hung on a shallow steel pipe post behaves differently than one on a proper concrete pad. We know what to expect block by block because we’ve worked these neighborhoods for decades.
Our Duncanville customers are homeowners who have lived in their houses twenty, thirty, sometimes forty years. They call us because they’re tired of tightening the same hinge every spring. When our crew leaves, the gate closes square and the latch lines up, and it stays that way. That’s the standard. Every job carries our written 90-Day Done Right Promise. If it’s not right, we come back and make it right. No paperwork, no arguing.
Victor Salinas leads a team of background-checked, uniformed technicians who work in your yard the way they’d work in their own mother’s. Calls from Duncanville are answered by a live person, not a phone tree, at any hour of the day or night.
Our Gate Repair Services in Duncanville
Electric Gate Repair
Electric gate repair in Duncanville frequently comes down to the operator fighting a gate that no longer swings freely. When a post tilts from clay movement, the operator strains on every cycle. Gears strip. Control boards overheat. We diagnose the whole assembly, not just the motor, because replacing a board on a gate that still drags is throwing money away. We service Viking, Ghost Controls, DoorKing, and Elite operators, among six other major brands.
Our technicians carry common control boards, receiver kits, and safety-edge components in the truck, so most electric gate issues in Duncanville are resolved in a single visit. The price is quoted and agreed before any work starts.
Automatic Gate Repair
Automatic gate systems in Duncanville’s older homes often date from the 1990s and early 2000s. The original operators frequently lack modern safety photocells and obstruction-reverse circuits. We can retrofit many of these older units, but sometimes the honest answer is replacement. If a 30-year-old control board fails and the motor has years of grit in the gearbox, a new operator costs less over three years than repeated board replacements. We’ll tell you which side of that line your gate falls on, and we’ll quote both options before you decide.
Hinge & Post Repair
This is the bread-and-butter of Duncanville gate work. The city’s residential build-out from roughly 1960 to 1985 used wood posts set in shallow concrete, and the Blackland Prairie clay has been working against those footings ever since. We regularly see gates where the post has jacked up out of the ground, or rotted at the base where moisture sat against the concrete collar. We re-set posts on footings augered below the clay’s active zone, replace rotted wood with steel where it makes sense, and re-hang the original gate when the wood is still sound.
Gate Realignment
A sagging gate in Duncanville is almost never fixed by tightening the hinges. The frame has gone out of square because the ground moved. We bring the leaf back to level and plumb, adjust the hinge positions, and where necessary add an anti-sag kit or turnbuckle. Then we set the latch height so the gate closes without lifting, even after the next wet spring. Realignment is part of most post re-sets we do here, and it’s the difference between a gate that works for a year and one that works for twenty.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Duncanville
Our technicians are trained and equipped on nine gate-automation brands, including Gate Repair systems built around Viking, Ghost Controls, DoorKing, Elite, LiftMaster, and FAAC. We maintain a parts inventory that covers the control boards and safety components most common in Duncanville’s older operators, which means fewer return trips and shorter wait times. Whether your system is a 1990s Viking buried under years of Texas dust or a newer Ghost Controls unit that was never quite dialed in, we will have the right part and the right training to make the correct fix on the first visit.
Common Gate Repair Problems We See in Duncanville Homes
- Post lean toward the alley. In the older 75116 neighborhoods, decades of clay heave lift the shallow footing under the latch-side post. The gate must be lifted to latch, and the fix is a full post re-set with a deeper footing, not a hinge adjustment.
- Rotted wood posts under brick ranch gates. Duncanville’s 1960s and 1970s homes often still have the original wood gate posts. Water sits against the buried portion, rot sets in, and the post eventually snaps at ground level. We replace wood with steel pipe where appropriate.
- Stripped gears from iced-over gates. Winter ice storms in the Dallas southwest suburbs add sudden weight-load stress. When a swing gate freezes against a tilted post, the operator forces it and strips internal gears. We address both the operator and the post realignment so it doesn’t happen again.
- Obsolete control boards with no safety edge support. Older Duncanville operators predate modern safety requirements. We can often retrofit photocells and edge sensors rather than replacing the whole system, and we’ll quote that option first when it’s practical.
Pricing for Gate Repair in Duncanville, TX
A typical post re-set in Duncanville, including augering a new footing below the clay’s active zone and re-hanging the gate, runs $450 to $900 per post depending on depth and whether the old concrete must be broken out. Hinge replacement on a standard residential swing gate typically falls between $150 and $350 per pair. Control board replacement runs $250 to $600 for most brands we service, including the part and labor. Full operator replacement generally runs $1,200 to $2,800 installed, depending on the opener style and safety features.
Here’s how costs break down for common Duncanville repairs:
| Service | Typical Range in Duncanville |
|---|---|
| Hinge replacement (per pair) | $150 - $350 |
| Post re-set with new footing | $450 - $900 per post |
| Gate realignment | $200 - $450 |
| Control board replacement | $250 - $600 |
| Full operator replacement | $1,200 - $2,800 |
Every estimate is free, and the price is quoted and agreed before any work starts. No surprises on the bill. Call (936) 226-3481 to schedule one. We also offer $50 off any repair over $250 and a free second opinion on any written estimate you’ve received from another company.
We Also Serve Cities Near Duncanville
Ironworks Gate Co. serves Duncanville and the surrounding communities of DeSoto, Lancaster, Cedar Hill, and Grand Prairie. If you’re in one of those cities and need a gate that closes right, call the same number and you’ll get the same crew. You can learn more about our Gate Repair in Duncanville coverage and service details on this page.
Serving Duncanville, TX - Our Local Coverage Area
We’re based in the Duncanville area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Repair in Duncanville
The gate isn’t leaning because the hinges are loose. The post under the latch side has a shallow footing, and the Blackland Prairie clay under it is swelling with moisture and lifting the post out of the ground. Tightening the hinge just moves the strain to the next weak point. The correct fix is to re-set the post on a footing augered below the clay’s active zone, typically 36 inches or deeper. Call (936) 226-3481 for a free assessment and a written quote.
Many 1970s and 1980s operators can accept retrofit photocell kits, but not all. If the control board has spare input terminals and the motor gearbox is still in good shape, retrofitting is often the cheaper short-term answer at roughly $300 to $600 installed. If the board is obsolete and the gears are already worn from years of dragging against a tilted post, full replacement is the more honest long-term fix. We’ll inspect it and quote both options. Estimates are free.
We can weld a cracked steel post when the surrounding metal is still sound, typically for $150 to $300. But on Duncanville’s clay soil, a cracked post base usually means the footing has already moved and the weld will fail again within a season or two. In most cases we recommend replacing the post entirely with a new steel pipe set on a deeper footing. The price is quoted and agreed before any work begins, so you’ll know the numbers before you decide.
For Duncanville’s expansive clay, a gate post footing should extend at least 36 inches below grade, with a concrete collar that reaches below the clay’s active swelling zone. Shallow 18-to-24-inch footings, which were standard on many 1960s and 1970s Duncanville homes, will continue to heave with seasonal moisture changes. Our post re-sets always include breaking out the old concrete, augering to 36 inches, and setting the post in fresh concrete with proper drainage. Call for a free estimate.
Not always, but often. On a double swing gate, if one post has heaved, the other has usually moved to some degree too, because both sit in the same clay and experience the same moisture cycles. We inspect both footings and quote each post separately, so you’re only paying for the work that’s actually needed. Most double gate re-sets in Duncanville run $900 to $1,800 for both posts, including footings and re-hanging. Call (936) 226-3481 for an exact quote.
Call Ironworks Gate Co. at (936) 226-3481 for a free estimate on gate repair in Duncanville. A live person answers, 24 hours a day, 7 days a week. The price is agreed before we start, and every job is backed by our written 90-Day Done Right Promise.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Duncanville since 1984.