Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGhost Controls Gate Repair in Midlothian, TX | Ironworks Gate Co.
We provide independent Gate Repair - Midlothian for Ghost Controls systems, and we see one failure pattern here more than anywhere else in Ellis County: concrete-encased posts tilting two to three degrees after a single wet season on Blackland clay, which throws Ghost Controls AXP and GTHD systems out of sync and burns up boards trying to compensate. You won’t get a canned “we fix all brands” answer from us. You’ll get a straight diagnosis of what the clay did to your gate, what’s salvageable, and what the repair will cost before we turn a single bolt. Call (936) 226-3481 for service anywhere in Midlothian.
Why Midlothian Residents Choose Us for Ghost Controls Service
Victor Salinas, our owner, grew up a few miles from the Ellis County Courthouse square in Waxahachie and studied electronics and industrial technology at Navarro College in Corsicana before spending more than two decades working on gates around Ellis County. That means when a Ghost Controls board fails in Midlothian, we don’t guess. We trace the circuit, identify the failed component, and tell you whether it’s worth repairing or replacing. Our technicians install, troubleshoot, and rebuild Ghost Controls actuators and boards weekly across Midlothian’s clay-heavy sites, and we stock the real component inventory: limit boards, harnesses, pinions, and sensor pairs that independent shops often have to order out for. We’re not manufacturer-affiliated or authorized; we’re the independent Ghost Controls sales & service team that’s been answering calls from Midlothian homeowners for years.
Common Ghost Controls Gate Repair Problems We Solve in Midlothian
- AXP limit boards corroding at the barrier-strip terminals. Midlothian’s cement plants (Martin Marietta, CRH/Ash Grove) put fine industrial dust in the air, and that dust settles on control boards. Mixed with North Texas humidity, it corrodes the barrier-strip terminals and the open/close limit logic drops. The gate opens fine, then refuses to close, or closes halfway and reverses. We clean or replace the board and seal the housing properly.
- TSS1 solar input circuits failing after ice storms. A Ghost Controls TSS1 solar-capable system is a good fit for a gate far from house power, but North Texas ice storms stress the charge controller. After a bad freeze, the input circuit fails and the gate sits dead on a cloudy week. We test the solar array and the controller, and we replace only the failed component, not the whole opener.
- LSM1 slide motor gearboxes stripping. Slide gates sit on tracks, and Midlothian’s Blackland clay heaves those track brackets every wet season. When the track binds, the LSM1 gearbox takes the load and strips. If the gears are gone, we replace the motor. If the track is the problem, we reset the brackets and realign the gate before it eats the next gearbox.
- GTHD dual-arm kits losing sync. The GTHD heavy-duty dual gate operator set has two arms that have to work together. When a swollen-clay post tilts one leaf, the other arm over-travels to compensate and trips the obstruction sensor. The gate stops halfway, reverses, or throws a bind code. We reset the tilted post, square both leaves, and reprogram the limits. Sometimes the board has been over-driven to the point of failure, and we replace that too.
- Phantom obstruction triggers from aftermarket clone boards. We regularly see Midlothian gates running off-brand clone boards that drift on timing and trigger obstructions that aren’t there. We replace them with genuine Ghost Controls boards. The real thing holds its programming; the clones don’t.
Ghost Controls Service in Midlothian: What Local Conditions Mean for Your Equipment
Midlothian’s new acreage subdivisions east of US-287 sit on the deepest Blackland clay in Ellis County. That clay swells dramatically in wet seasons and contracts in drought. We routinely find Ghost Controls gates there whose concrete-encased posts tilt two to three degrees after a single wet season. That’s a failure pattern we rarely see in Mansfield or west Waxahachie, where the soil drains faster and doesn’t heave the same way. Out in the Shiloh Ridge acreage subdivision off Plainview Road, our tech found a Ghost Controls GTHD double-swing gate that would start, stall, and throw a ‘bind’ code every afternoon. The posts hadn’t rusted. The west post had tilted 2.5 degrees over one wet spring, pinching the leaf against the latch post. We dug out the concrete collar, reset the post in a deeper footing with gravel drainage, squared both leaves, and replaced the original GTHD limit board that had been over-driven trying to compensate for the bind. If your gate “suddenly” drags or won’t close after a rainy stretch, the motor is probably fine and the post is the problem. That’s the Midlothian difference, and it’s why we always check post plumb before we touch the operator.
Ghost Controls Models & Products We Service in Midlothian
We service the full Ghost Controls lineup in Midlothian: the AXP and AXDP automatic gate opener kits, the TSS1 and TDS2 solar-capable swing and slide systems, the LSM1 and LSM2 linear slide motors, and the GTHD heavy-duty dual gate operator sets. On control-plane repairs we use genuine Ghost Controls boards, actuators, and limit switch assemblies. Off-brand clones drift on timing and trigger phantom obstructions, so we won’t install them. For mechanical wear items like pinions, hinges, and arm brackets, we use US-sourced aftermarket steel that matches or exceeds OEM tolerance. We’ll rebuild a Ghost Controls opener when the actuator and board are still healthy. When resetting posts and replacing a corroded board costs more than a new operator kit, we tell you that straight, with numbers, and let you decide.
Ghost Controls Service Pricing in Midlothian
Ghost Controls gate repair in Midlothian typically falls in these ranges:
| Service | Typical Price Range |
|---|---|
| AXP/TSS1 limit board replacement (genuine Ghost Controls) | $180-$340 |
| LSM1/LSM2 slide motor gearbox replacement | $220-$385 |
| GTHD dual-arm sync and limit reset | $150-$275 |
| Gate realignment (post reset, leaf square-up) | $200-$450 |
| Hinge and post repair (weld or replace, re-set post) | $175-$400 |
| Full service call diagnosis | $89 seasonal tune-up covers inspection |
The final price depends on whether the post needs resetting, which is common in Midlothian, and whether the board is salvageable. Every estimate is free, and the price is quoted and agreed before any work starts. You’ll know the number before we touch your gate. Call (936) 226-3481 for an exact quote on your Ghost Controls system.
Serving Midlothian, TX - Our Local Coverage Area
We’re based in Midlothian, TX and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Ghost Controls Gate Repair in Midlothian
When the Blackland clay swells after rain, it heaves the gate post and the gate binds against the latch post. The AXP board reads that as an obstruction and refuses to close. The fix is resetting the post, not replacing the board; if the board has been fighting the bind for months, it may need replacement too. Call (936) 226-3481 and we’ll diagnose it on site.
Usually yes, if we get to it before the board corrodes. We open the housing, dry and clean the internals, test the transformer and relays, and replace the board only if it’s already failed. Floodwater with cement dust in it is especially corrosive; don’t power the gate back on yourself. A trained professional should inspect it first, because a wet board can short and take the actuator with it.
Martin Marietta and Ash Grove dust settles on control boards, hinges, and limit switches. Mixed with humidity, it corrodes terminals and pits metal. We see AXP boards fail at the barrier-strip terminals from exactly this. Regular cleaning and sealed housings help, but the only real defense is catching corrosion early. Call (936) 226-3481 and we’ll inspect your board before it fails.
Dry weather contracts the Blackland clay under the track brackets, pulling the track out of line just enough to bind the rack and pinion. A good rain swells the clay back and relieves the bind, which is why it works again. The permanent fix is resetting the track brackets below the shrink-swell zone and realigning the rack. We do that work regularly across Midlothian.
No. The post gets reset, the gate re-squared, and the operator usually survives. We replace a Ghost Controls opener only when the actuator and board have both been damaged beyond practical repair. We’ll show you exactly where the failure occurred and give you a straight repair-versus-replace conversation before any work starts. Call (936) 226-3481 for a free estimate.
Service Areas Near Midlothian
Our Ghost Controls service covers Midlothian and the surrounding communities, including Ghost Controls service in Waxahachie, Ghost Controls service in Ennis, Oak Leaf, Red Oak, and Ovilla. We’re on Midlothian driveways every week, and we answer the phone around the clock.
Book Your Ghost Controls Service in Midlothian Today
If your Ghost Controls gate is misbehaving, call (936) 226-3481. We answer live, 24 hours a day, and we’ll get a technician to your Midlothian property fast. Free estimates, upfront pricing, and the 90-Day Done Right Promise on every job.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Midlothian and Ellis County for over two decades.