Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFAAC Gate Parts & Welding in Waxahachie: What to Know First
We provide independent FAAC gate parts and welding in Waxahachie, with most hinge, post, and weld repairs completed in a single visit. A typical FAAC gate repair involving parts and welding runs between $225 and $650, and you will always know the price before we start. We are not an authorized FAAC dealer, but we have been working on FAAC 400, 412, 750, 770, 840, and C720 systems around Ellis County for years, and we fix them properly. If you have a FAAC gate that will not close right, a hinge pulling loose, or a post that has rusted at the base, call (936) 226-3481 and a live person will answer.
How FAAC Products Fail - and How We Fix Them
FAAC builds a solid operator, but the metal and mounts around it take a beating in North Texas. Here is what we see in Waxahachie driveways, and how we address it.
- Hinge wear on 400 and 412 series swing gates. These residential swing operators are common in older Waxahachie neighborhoods, and the gate leaves are heavy. Over time the hinge barrel elongates and the leaf sags, which makes the FAAC operator fight the gate on every cycle. We cut out the old hinge, weld in a new one with the gate properly shimmed, and set the operator limits again. That last step is the one most generalists skip.
- Base rust on posts in blackland clay. Waxahachie sits on expansive clay that holds moisture against steel. A gate post sunk in concrete twenty years ago will often rust through right at ground level, while the post above still looks fine. We see this on FAAC-equipped gates because the operator keeps working and masks the structural problem. We replace the post, weld the hinge plates, and re-hang the gate to the FAAC operator’s throw.
- Leaf frame fatigue on C720 and 750 series sliders. The C720 is a workhorse, but a sliding leaf that racks or twists will bind in the track and trip the FAAC’s obstruction sensor repeatedly. We check the leaf for square, weld reinforcement where the frame has fatigued, and replace the rollers if they have flat-spotted. The operator gets a straight, true leaf to move, and the false trips stop.
- Weld failure at the gate latch mount. This is not a FAAC problem exactly, it is a metal fatigue problem that shows up on any gate that gets thousands of open and close cycles a year. But with a FAAC sitting on the leaf, a loose latch lets the gate flex in ways the operator was not designed for. We grind back the old weld, fixture the latch plate properly, and run a full-penetration weld so it stays put.
- Stripped or seized hinge bolts on older FAAC installations. What to check before drilling or cutting: the original installer may have used zinc-plated bolts that have now fused with the iron hinge. We drill them out carefully, chase the threads, and install new hardware with anti-seize. If the leaf is too far gone, we cut and re-weld a new hinge plate. On a hot Waxahachie afternoon, that is the difference between a two-hour repair and a broken drill bit in your gate.
Our FAAC Gate Parts & Welding Process
Here is the sequence we follow on a typical FAAC parts and welding visit in Waxahachie, from the first call to the last sweep of the driveway.
- 1
You call, we listen. A live person answers at (936) 226-3481, 24 hours a day. We ask what the gate is doing, what brand is on the operator, and what you have already tried. Then we schedule the visit.
- 2
We diagnose before we quote. Victor Salinas or one of our background-checked technicians walks the gate, checks the leaf, the hinges, the posts, and the FAAC operator settings. We explain what failed and why, in plain English, before we ever talk price.
- 3
Parts decision: OEM or quality aftermarket. We are independent, so we can source whichever part makes sense. For FAAC-specific boards and limit switches, we recommend OEM or proven aftermarket equivalents. For hinges, weld plates, and structural steel, we typically fabricate on the truck or use locally sourced heavy-gauge material. We will tell you the trade-off and let you decide.
- 4
The repair, in one visit. Most welds, hinge replacements, and post repairs are done the same day. We cut out the bad metal, prep the surface, weld, grind, and paint. The gate gets re-hung and the FAAC operator gets re-set to match the new geometry.
- 5
We test it, then you test it. The gate cycles several times under load. We check the FAAC force settings and obstruction behavior. Then you open and close the gate from the keypad, the remote, and the manual release.
- 6
We clean up and you get the promise. We sweep the work area, walk you through what was done, and hand you the written 90-Day Done Right Promise. If it is not right, we come back and make it right. No arguing, no paperwork, no exceptions.
What FAAC Gate Parts & Welding Costs in Waxahachie
The price depends on how much metal has to be cut out and replaced. Here are the ranges we quote most often for FAAC-equipped gates in Waxahachie:
- Hinge replacement, single leaf: $180 to $320, including welding, shimming, and operator re-setting.
- Post replacement with concrete work: $350 to $700, depending on post size, depth, and whether we have to match stone or brick.
- Gate leaf straightening and weld reinforcement: $200 to $450, plus any roller or track work.
- Latch or lock mount re-weld: $120 to $250, including grinding, welding, and re-painting.
- Custom welding (brackets, stops, reinforcement plates): $95 to $220 per piece, depending on size and access.
What moves the price is usually rust: if the post base is rotted, we have to dig, pour, and re-set before the welding starts. We quote the full job before a single bolt is turned, so the number on your estimate is the number on your invoice. Call (936) 226-3481 for an exact quote on your FAAC gate. Estimates are free.
Why Waxahachie Homeowners Call Ironworks Gate Co. for FAAC Work
We have been serving Waxahachie since 1984, and we plan to be here another forty years. The owner, Victor Salinas, grew up a few miles from the Ellis County Courthouse square, and he still runs the company the way his father ran a small welding shop: do the work right, charge a fair price, and stand behind it. Every FAAC job we complete is covered by our written 90-Day Done Right Promise. Our technicians are background-checked and uniformed, and they work on your property the way they would work on their own mother’s driveway. If it rolls, swings, or slides, we can tell you what is wrong with it, and whether it is worth fixing. And if your next gate turns out to be a LiftMaster, Mighty Mule, Ghost Controls, or DoorKing, we handle those too, with the same guarantee.
FAQs
In most cases, yes. We stock common FAAC repair parts and carry welding equipment on our service trucks, so a hinge, latch, or post repair can often be completed in a single Waxahachie visit. Call (936) 226-3481 and we will tell you honestly what we can do today and what has to wait for materials.
We use OEM parts where they matter: FAAC control boards, limit switches, and any component that talks to the operator’s logic. For structural parts like hinges, posts, and weld plates, we often fabricate from heavy-gauge steel that meets or exceeds the original spec. We will walk you through the choice before any work begins, and the price reflects exactly what we install.
No. We are an independent FAAC service provider, not an authorized dealer, so manufacturer warranty claims on the operator itself must go through an authorized FAAC rep. However, every repair we make, including all welding and parts installation, is covered by our own written 90-Day Done Right Promise in Waxahachie and the surrounding area.
We look at the leaf, the hinges, and the posts before we recommend anything. If the metal is rusted through at the base or the leaf has twisted beyond what straightening can correct, replacement is often cheaper in the long run. If the frame is sound and only a hinge or bracket has failed, welding is almost always the right call. We will show you the failure and explain our reasoning before you spend a dollar.
A full installation includes the gate leaf, posts and hinges, the FAAC operator, the power run, safety edges or photocells, and any keypad or remote setup you want. We measure, order, schedule, and install with a written price agreed before work starts. This is measured work and it is scheduled, not dispatched, but the estimate is always free. Call (936) 226-3481 to set one up.
Contact
If your FAAC gate is sagging, dragging, or refusing to hold its settings, call Ironworks Gate Co. at (936) 226-3481. A live person answers 24 hours a day, 7 days a week. We will talk through what is happening, schedule a visit to your Waxahachie property, and give you a written, upfront price before any work begins. Free estimates, senior and veteran discounts always apply, and every job is backed by the 90-Day Done Right Promise.
Written by Victor Salinas, Owner, Ironworks Gate Co. at Ironworks Gate Co., serving Waxahachie and nearby areas.